The biggest difference in the pressure of the sprinkler is that the filter is clogged. Reasons for filter plugging:
First, the water source problem. Many customers divert water, which is often from ponds, rivers, etc. There are too many impurities in the water. When pumping, the filter screen is easily blocked by debris, such as sand, plastic bags, green vines, algae, or some sundries. . When the water source mixed with debris enters the pipeline, water pump and water tank through the water inlet, it may cause blockage. Even after entering the tank smoothly, during the drainage process, the water outlet pipe may be caused, the water pump is blocked, and the water is discharged. At the end, straight and back sprinkling is not possible to discharge smoothly. After these things are pumped into the tank, the sprinkler will spray the water out. Also, with the direction of the water flow, these impurities will gradually accumulate in the filter screen. If it is long, the filter will be blocked and the water flow will be difficult to pass, resulting in a decrease in water flow;
Second, the problem of water rust. When the sprinkler is relatively old, there will be some rust inside the tank. The longer the rust is generated, the more the filter will be blocked.
Third, the filter is aging or damaged. When the filter is clogged, it will be washed by a certain pressure of water, which may be broken or damaged. In addition, if the filter is used for a long time, it may also be aging, or the filter may be cleaned frequently, causing damage to the filter. The debris enters the inside of the pipeline, causing blockage and causing a decrease in water flow;
Fourth, there are debris in the tank. Because there is a personal orifice above the tank of the sprinkler, if it is not closed, or if there is any debris entering the tank, it will cause the pressure in the tank to be blocked, and the pressure will be too small, and the amount of water will become smaller;
5. The pressure on the sprinkler pump is insufficient. As a result, the sprinkler pump can't pump water, and the insufficient pressure of the sprinkler pump is usually caused by two reasons:
1, the power is too low, the speed is too low, try to increase the throttle;
2. The impeller flow path or the suction line is blocked, or the impeller wear is broken. If it is blocked, the pump should be cleaned. If the impeller is damaged, the impeller needs to be replaced.
If you have any questions or questions about the special car, you can also inquire!
Consult the car hotline: 158-9759-8261 (WeChat with the same number)
Business QQ: 348672181
In the edible oil pressing plant, before the extrusion of oil from oil containing materials, an oil pretreatment process is typically undertaken to improve the efficiency of production and to ultimately save on costs. The entire oil milling process generally includes: cleaning, sieving, hulling, separation, cracking, particle making, frying, softening, flaking, drying, and expelling oil materials. The process: cleaner --> sheller --> huller --> crusher / flaker --> steam cooker --> softening --> extruder --> dryer.
Oil Pressing Plant Pretreatment
- Organic impurities, such as stems and leaves, cords and chemical fibers.
- Inorganic impurities such as soil and metal.
Advantages of Our Oil Pretreatment Technology
- Heated shelling features means to reduce energy consumption.
- Double dehulling process which raises the shelling ratio to up to 85% with oil residue in hulls reduced to below 1.5%.
- Large-volume silos to facilitate adjustments to production capacity.
- Can produce oil cake as different grades and various protein levels which are adjustable to meet special requirements. Soybean cake can also be milled.
- With years of research experience on screw Oil Press machine ,we can reach residual oil and low energy consumption.
- Complete pre-treatment system can be controlled automatically.
The Goal of Oil Pretreatment
- Improve the quality of the oil and the cake.
- Increase rate of productivity; reduce residual oil.
- Increase treatment capabilities of the equipment.
- Lessens wear and lengthens the life of the equipment.
- Ensures safety.
- Expansion improves the rate of productivity and the quality of the oil cake.
Oil Pretreatment Process
- Warm hulling process reduces energy consumption.
- Double cracking and hulling process improves the hulling ratio and reduce oil residue in the hull.
- High volume hull bin makes production flexible.
- Makes it possible to produce meals of various protein content (includes meal milling).
- Adopts the complete explosion puffing process.
- Automated controls.
Vegetable Oil Pressing Plant Turnkey Project
Cottonseed Vegetable Oil Pressing Plant Turnkey Project ,Soybean Oil Pressing Plant Turnkey Project ,Palm Oil Pressing Plant Turnkey Project ,Sunflower Oil Pressing Plant Turnkey Project
Hebei Huipin Machinery Co.,LTD , https://www.oilpresschina.com