Plastic Recycling and Extrusion Machine Manufacturer for PP Non-Woven

Introduction:
1. Feeding: as standard design, plastic scraps such as film, filament, raffias conveyed into the compacting room through belt conveyor; to handle rolls' scraps, roll hauling off device is an optional feeding method. Motor drives of conveyor belt and hauling device cooperate with ABB inverter. Feeding speed of conveyor belt or roll hauling off is fully automatic based on how full the compactor's room is. Metal detector can be combined with belt conveyor, and can interlock with control system, to warn and stop the system, in case that metal is found in feeding section.

2. Crushing and compacting: the rotatory blades of compactor will cut up incoming scraps. Frictional heating which caused by high speed rotatory blades will heat and let scraps shrinking just below their agglomerating point. Optimal designed guide structure compacts the material and directs it into extruder screw. Crushes, dries and compacts the material which enables a fast and stable feeding from the compactor directly into the extruder.

3. Plasticization and degassing: A specialized single screw extruder applied to gently melt the pre-compacted material. The plastic scraps will be well melted, plasticized in a 32 to 34D processing section. With double-zone vacuum degassing system, volatiles such as low molecular and moisture will be removed efficiency, especially suitable to heavy printed film and material with some water content.

4. Melt filtration: a regular single-plate/ piston double-station screen changer or non-stop double-plate/ piston four-station can be installed on head of extruder to present significant filtration performance. The requirements on the filter technology depend heavily on the quality of the input material as well as the planned use of granules.

5. Pelletizing: die-face water ring pelletizing system set as the standard granulating method in ML series. Self-adjusting pelletizing head for the best granulate quality and long uptime thanks to consistently correct blades pressure. RPM of rotatory blades is automatic based on melt extruding pressure. Advanced dewatering vibration sieve combining with horizontal-type centrifugal dewatering present high performance dried pellets.

Photos for reference:






Main technical parameter: 
In order to match your requirement and provide you a proper quotation, please advise:
• What material do you want to recycling? PE film? PP woven bag? HDPE/PP bottle? or other plastic?
• What capacity(kg/h) do you want?
• What is the final size(mm) of granules you want?
• Other special requirements about the PE plastic pelletizing machine you want.

Our service:
Before-sale
• Introduce products in detail   
• Recommend suitable solution   
• Offer test

During manufacturing
• Provide layout and engineering conditions   
• Offer screw plan and related documents
• Inform the project processing status   
• Insure the product designed in accordance with technical document

After-sale
• Provide installation, commissioning and training   
• Offer spare parts
• Provide necessary technical support and update information

Feel free to contact with me if you want to leanr more information.
Contact persion:Ms. Laura
Mob.: 86 159 6236 6319 Introduction:
1. Feeding: as standard design, plastic scraps such as film, filament, raffias conveyed into the compacting room through belt conveyor; to handle rolls' scraps, roll hauling off device is an optional feeding method. Motor drives of conveyor belt and hauling device cooperate with ABB inverter. Feeding speed of conveyor belt or roll hauling off is fully automatic based on how full the compactor's room is. Metal detector can be combined with belt conveyor, and can interlock with control system, to warn and stop the system, in case that metal is found in feeding section.

2. Crushing and compacting: the rotatory blades of compactor will cut up incoming scraps. Frictional heating which caused by high speed rotatory blades will heat and let scraps shrinking just below their agglomerating point. Optimal designed guide structure compacts the material and directs it into extruder screw. Crushes, dries and compacts the material which enables a fast and stable feeding from the compactor directly into the extruder.

3. Plasticization and degassing: A specialized single screw extruder applied to gently melt the pre-compacted material. The plastic scraps will be well melted, plasticized in a 32 to 34D processing section. With double-zone vacuum degassing system, volatiles such as low molecular and moisture will be removed efficiency, especially suitable to heavy printed film and material with some water content.

4. Melt filtration: a regular single-plate/ piston double-station screen changer or non-stop double-plate/ piston four-station can be installed on head of extruder to present significant filtration performance. The requirements on the filter technology depend heavily on the quality of the input material as well as the planned use of granules.

5. Pelletizing: die-face water ring pelletizing system set as the standard granulating method in ML series. Self-adjusting pelletizing head for the best granulate quality and long uptime thanks to consistently correct blades pressure. RPM of rotatory blades is automatic based on melt extruding pressure. Advanced dewatering vibration sieve combining with horizontal-type centrifugal dewatering present high performance dried pellets.

Photos for reference:






Main technical parameter: 
In order to match your requirement and provide you a proper quotation, please advise:
• What material do you want to recycling? PE film? PP woven bag? HDPE/PP bottle? or other plastic?
• What capacity(kg/h) do you want?
• What is the final size(mm) of granules you want?
• Other special requirements about the PE plastic pelletizing machine you want.

Our service:
Before-sale
• Introduce products in detail   
• Recommend suitable solution   
• Offer test

During manufacturing
• Provide layout and engineering conditions   
• Offer screw plan and related documents
• Inform the project processing status   
• Insure the product designed in accordance with technical document

After-sale
• Provide installation, commissioning and training   
• Offer spare parts
• Provide necessary technical support and update information

Feel free to contact with me if you want to leanr more information.
Contact persion:Ms. Laura
Mob.: 86 159 6236 6319

PVC Wire Harness Protecting Sleeving 

1.PVC Protection Sleeving, Bundles cables at any point along the run, easily avoiding large connectors and plugs for quick and easy
   installation

2.Zipper Wire Harness Sleeving, provides maximum security for cables, unlike other side-entry or split braided sleeving that can easily
   be removed by accident

3. Wire Protection Sleeve, Heavy duty pvc construction ensures great durability

4. Wire Harness Protecting Sleeving  and  Cloth Wire Sleeving  is ideal for quick and easy cable management in homes, offices, and even industrial facilities.

5.Certificated by UL,ROHS, REACH,HALOGEN FREE

What is the Details of our Zip Up PVC Cable Sleeving?

Usage	Cable/wire Bundling,Protection,Management Solution
FOR what Field	Ideal for quick and easy cable management in homes, offices, and even industrial facilities
Sleeve Material	PVC
Zipper Material	PVC
Size	25mm ID*3mL
Color	Black
Packaging	1pc/zipr bag,100PCS/Ctn,18.50Kgs/Ctn
Carton Size	53*53*40cm or customized
Free Sample	Available
Full Size Sample Lead time	As usual 3-7 working days
Production Lead time	10-15days

Application:

Wire Harness Protecting Sleeving

PVC Protection Sleeving,Wire Harness Sleeving,Wire Protection Sleeve,Cloth Wire Sleeving

KEYUACE Materials Co., Ltd. , https://www.insulationtubing.com